One stop shop for
precision engineered parts.
We build to your print. PNA Technologies is an ITAR-registered converter working in EMI/RFI shielding, thermal management, electrical insulation, and rubber gasketing, and we run MIL-STD materials whenever your drawing calls for them.
- ISO 9001:2015
- ITAR Registered
- DFARS Compliant
- Made in USA
under one roof
specified features
submitted drawings
Prototype to production
at a glance
A material converter
built for hard programs.
We convert material for defense, automotive, aerospace, telecommunications, medical, and industrial electronics customers, all out of one ITAR-registered shop in Jamaica, New York.
We are a small, high-capability shop, and we would rather be known for parts that fit than for promises that don’t.
Our work covers the full range of aerospace and defense, on land, at sea, and in space. Complex shapes, awkward structures, and the fabrication jobs other converters pass on are the ones we tend to get called about.
Deep material knowledge, years on the floor, and a documented quality system are what let us turn conductive and non-conductive flexible materials into parts that meet print the first time, and every lot after that.
Build to print
You send the drawing. We hold the specification. Dimensions, material, tolerance, and finish come back exactly as you called them out.
Advanced capabilities
Digital X-Y knife cutting and CAD-driven programming handle complex shapes and tight features without any die tooling, so revisions cost you time instead of money.
Material knowledge
We know how EMI elastomers, foils, thermal interface materials, films, and sealing compounds behave, and we stock MIL-STD grades when the print specifies them.
Quality documented
An ISO 9001:2015 quality system stands behind the work. Ask and you get First Article Inspection, dimensional reports, and certificates of conformance with the shipment.
Six lines,
one floor.
Shielding, thermal, insulation, and sealing parts all run through the same CAD-driven workflow, the same inspection discipline, and the same quality system. Nothing gets a shortcut.
EMI / RFI Gaskets
Conductive elastomer gaskets, fabric-over-foam, and shielding die-cuts converted to print for enclosure and LRU joints.
Conductive O-Rings
Silver- and nickel-graphite filled elastomer O-rings for continuous ground paths in sealed connector and housing interfaces.
Thermal Management
Gap pads, phase-change materials, and adhesive thermal interface die-cuts that move heat off power electronics.
Electrical Insulation
Dielectric barriers and insulators converted from Nomex, Mylar, Kapton, and comparable films to exact geometry.
Gaskets & Seals
Non-conductive sealing parts in silicone, EPDM, Viton, foams, and sponge for environmental, weather, and compression duty.
Flange Gaskets
Conductive elastomer mounting-flange gaskets for connectors, waveguides, and enclosure interfaces.
Land, sea,
air, and space.
PNA parts ship into programs where failure is not an option, and into commercial electronics that hold the same tolerances for very different reasons.
Defense Electronics
- Radar & EW enclosures
- Tactical radio shielding
- C4ISR chassis seals
- MIL-STD materials
Aerospace & Avionics
- Avionics LRU gaskets
- Display & control housings
- Engine control units
- Cabin electronics
Space & Satellite
- Antenna flange gaskets
- Low-outgassing compounds
- CubeSat enclosures
- Ground terminals
Uncrewed Systems
- Flight computer shielding
- Datalink modules
- Payload sealing
- Mass-optimized parts
EV & Automotive
- Battery management seals
- Inverter EMI gaskets
- Charge port sealing
- Thermal interface pads
Medical & Telecom
- Imaging & diagnostic housings
- RF enclosure shielding
- 5G base station gaskets
- Instrumentation seals
Die-free conversion,
verified dimensions.
Two machines do most of the heavy lifting: a computer-controlled digital cutter that works straight from your CAD file, and a vision system that measures what comes off it.
Zünd X-Y knife cutter
Programmed straight from your DXF or STEP file, the Zünd cuts sheet and stock to exact print geometry without die tooling. One prototype and a full production run use the same setup and hold the same accuracy.
Keyence vision measuring system
This high-resolution system measures parts optically, without touching them, and prints a dimensional report. We check test cuts on it before scaling a run, then use it again for First Article Inspection and lot uniformity records.
Every part walks the same five stages: collaboration, programming, verification, production, delivery.
Built in.
Not bolted on.
These are the registrations and standards that let our parts enter controlled programs. All current, all documented, and all available with your shipment if you ask.
Registrations & standards
ISO 9001:2015
A certified quality management system that governs every order, from the RFQ through the delivery.
ITAR registered
Your controlled technical data and drawings are handled under our registration with the U.S. State Department.
DFARS compliant
Domestic specialty-metal and material sourcing per DFARS 252.225-7009 wherever it applies to your part.
Sourcing & documentation
SAM.gov active
Registered and active for federal and prime-contract awards. CAGE and DUNS available on request.
MIL-STD materials
When your print calls out a military specification, that is what we buy and cut, MIL-DTL-83528 included.
Made in USA
Cutting, inspection, and packaging all happen at our Jamaica, New York facility. Nothing is sent offshore.
Why teams
build with PNA.
The reasons programs keep coming back to us, from a first prototype through full-rate production.
ISO 9001:2015 registered
A certified manufacturer with a quality system that follows every order from start to finish.
Materials in stock
Tier-one stocking relationships across EMI, thermal, insulation, and sealing materials keep our lead times short.
Expert engineering
Real technical and material knowledge on the phone with you, from the RFQ through to completion.
Communication throughout
You hear from us from the RFQ through on-time delivery. No black box, no surprises.
Continuous improvement
We keep looking for ways to make the next part better than the last one.
Send us your drawing.
We'll take it from there.
Send dimensions, material, tolerance, quantity, and the date you need it. You’ll hear back within 24 business hours with feasibility, lead time, and price.